HARMAN KARDON HK3475
Manual de Servicio

hk3475
4. Stations may also be tuned directly by pressing the Direct Button �, and then pressing the Numeric Keys � that correspond to the station�s frequency. The desired station will automatically be tuned. NOTE: When the FM reception of a station is weak, audio quality will be increased by switching to Mono mode by pressing the FM Mode Button * � until the Stereo Indicator F goes out. Preset Tuning Up to 30 stations may be stored in the HK 3475�s memory for easy recall using the front panel controls or the remote. In order to program preset stations into memory, you must use the remote control. To enter a station into the memory, first tune the station using the steps outlined above. Then: 1. Press the Memory Button ø on the remote. The Memory Indicator E and Preset Indicator C will light and flash in the Main Information Display �. 2. Within five seconds, press the Numeric Keys � corresponding to the location where you wish to store this station�s frequency. The preset number will appear in the Preset Number B display. 3. Repeat the process after tuning any additional stations to be preset. Auto Preset � Preset stations may also be programmed automatically for the entire FM band. To automatically enter each station that may be tuned with acceptable quality into the HK 3475�s preset memories, first select the FM band. Next, press and briefly hold the Auto Preset Button ¬ until the Memory Indicator E and Preset Indicator C begin to flash, and the station frequency indication begins to increase. Release the button and the tuner will search the entire FM band, and stop briefly at each station that has acceptable signal strength. The HK 3475 will automatically assign a preset number to each station, and then search for the next station. The automatic scan process will stop when all 30 preset memory locations have been filled or the entire FM band has been scanned three times. NOTE: Using the automatic tuning mode in areas with more than 30 FM stations will completely fill the preset memories, and overwrite any previously memorized presets for either AM or FM stations. TIP: The automatic scan process may enter stations that you do not wish to retain in the memory, or it may enter a station on more than one frequency if the signal is too strong. These unwanted stations may be removed from the memory using the Preset Clear function outlined below. Recalling Preset Stations � To manually select a station previously entered in the preset memory, press the Numeric Keys � that correspond to the desired station�s preset memory location. � To manually tune through the list of stored preset stations one by one, press the �/¤ Preset Buttons %� on the front panel or remote. � To automatically scan through the stations entered in the preset memory, press the Preset Scan Button @ � on the front panel or remote. The tuner will cycle through the list of preset stations in the Preset Number Display B, stopping for five seconds at each one. Press the button again to stop the scan at your desired station. Clearing Preset Stations Unwanted preset stations may be erased from the unit�s memory to make it easier to tune only those stations you want. To remove a preset station from the HK 3475�s tuner memory, first tune to the station using the Preset Scan Button @ � on the front panel or remote, or by entering the preset number directly, using the Numeric Keys �. When the preset station to be removed has been tuned, first press the Memory Button ø. The Memory Indicator E and Preset Indicator C in the Main Information Display � will flash, and the actual preset number will disappear from the Preset Number B display. Next, press the Clear Button � within five seconds. The preset station will be removed from the memory, and the action will be confirmed by the brief appearance of the word CLEAR and the preset number location in the Main Information Display. That memory location will now be empty, and you may program a different station to that location, or leave it empty.

OPERATION
Tape Recording
In normal operation, the audio source selected for listening through the HK 3475 is sent to the Tape Mon Out � and Tape 2 Rec Out ¤ outputs. This means that any program you are listening to may be recorded simply by placing machines connected to the outputs for Tape Monitor � or Tape 2 ¤ in the record mode. When a tape recorder with separate record and playback heads is used, you may monitor the output of the recording by pressing the Tape Monitor Input Selector 9ç. The T-Mon Indicator J will light in the Main Information Display � to remind you that you are listening to the record playback instead of the actual input source being recorded. Press it again to hear the input source. IMPORTANT NOTE: Please make certain that you are aware of the copyright restrictions on any material you copy.

23

OPERATION

23